DT-type
Mr Lei 15817842088 Mr Cao 15899819318
Mr Chen 13790083198 Mr lü 13420665088
Ms Yao 15019622678 Ms Li 13600326220
1. Fixed hollow shaft, most suitable for automatic vertical operation.
2. can bear the large smuggling disk, suitable for large load rotary disk drive occasions.
3. Suitable for horizontal installation only, unable to be installed vertically or upside down.
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 520 |
Output shaft allowable axial load | C2 | kgf | 220 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 220 |
Input shaft bending moment | C4 | kgf | 160 |
Input shaft maximum torque | C5 | kgf-m | 9.5 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 0.03 |
Positioning accuracy | sec. | ±30 | |
Weight | kg | 20 |
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 860 |
---|---|---|---|
Output shaft allowable axial load | C2 | kgf | 420 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 300 |
Input shaft bending moment | C4 | kgf | 250 |
Input shaft maximum torque | C5 | kgf-m | 25 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 0.01 |
Positioning accuracy | sec. | ±30 | |
Weight | kg | 50.0 |
The GD2 of the input shaft is the value within the stop range。
C1~C5 value is the value when the safety factor = 2 is reached。
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 1050 |
---|---|---|---|
Output shaft allowable axial load | C2 | kgf | 720 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 500 |
Input shaft bending moment | C4 | kgf | 350 |
Input shaft maximum torque | C5 | kgf-m | 53 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 0.07 |
Positioning accuracy | sec. | ±30 | |
Weight | kg | 85 |
The GD2 of the input shaft is the value within the stop range。
C1~C5 value is the value when the safety factor = 2 is reached。
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 1500 |
---|---|---|---|
Output shaft allowable axial load | C2 | kgf | 1100 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 1200 |
Input shaft bending moment | C4 | kgf | 960 |
Input shaft maximum torque | C5 | kgf-m | 220 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 0.23 |
Positioning accuracy | sec. | ±30 | |
Weight | kg | 190.0 |
The GD2 of the input shaft is the value within the stop range。
C1~C5 value is the value when the safety factor = 2 is reached。
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 1950 |
---|---|---|---|
Output shaft allowable axial load | C2 | kgf | 1520 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 1570 |
Input shaft bending moment | C4 | kgf | 1130 |
Input shaft maximum torque | C5 | kgf-m | 460 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 0.62 |
Positioning accuracy | sec. | ±30 | |
Weight | kg | 450.0 |
The GD2 of the input shaft is the value within the stop range。
C1~C5 value is the value when the safety factor = 2 is reached。
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 2500 |
---|---|---|---|
Output shaft allowable axial load | C2 | kgf | 1800 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 1900 |
Input shaft bending moment | C4 | kgf | 2250 |
Input shaft maximum torque | C5 | kgf-m | 670 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 0.86 |
Positioning accuracy | sec. | ±30 | |
Weight | kg | 500.0 |
The GD2 of the input shaft is the value within the stop range。
C1~C5 value is the value when the safety factor = 2 is reached。
PROJECT | SYMBOL | UNIT | VALUE |
Allowable radial load of output shaft | C1 | kgf | 4500 |
---|---|---|---|
Output shaft allowable axial load | C2 | kgf | 3300 |
Output shaft allowable torque | Ts | kgf-m | Reference torque table |
Input shaft allowable radial load | C3 | kgf | 2800 |
Input shaft bending moment | C4 | kgf | 3800 |
Input shaft maximum torque | C5 | kgf-m | 1000 |
GD2 of input shaft (Note 1) | C6 | kgf-m2 | 2.7 |
Positioning accuracy | sec. | ±20 | |
Weight | kg | 1200.0 |
The GD2 of the input shaft is the value within the stop range。
C1~C5 value is the value when the safety factor = 2 is reached。